Home > TPMS Relearn and Programming Instructions > Cadillac TPMS Relearn

Can't find TPMS relearn instructions for your vehicle? Please email us at [email protected] for Cadillac TPMS Relearn information.

Schrader 28206 Rubber Valve Snap-In TPMS Relearn Procedure

1. Apply the handbrake and put the gear selector in position P.
2. Turn the ignition switch to ON.
3. Press the MENU button and select the Vehicle information menu.
4. Turn the settings knob and select Pressure monitoring system
5. Push in the SET/CLR button and keep it depressed for 3 seconds to start the matching procedure for the tire pressure sensors. The message "Are you certain that you want to start the procedure?" will be displayed.
6. Press in the SET/CLR button again to confirm the selection. The car horn sounds twice and the blinkers flash to indicate that the tire pressure monitoring receivers are in the programming mode. The message "Tire pressure programming active" appears on the driver information display.
7. Begin with the front tire on the driver's side.
8. Remove the valve cap from the valve. Activate the TPMS sensor by either increasing or decreasing the tire pressure for five seconds or until the horn sounds. It can take up to 30 seconds until the horn sounds. The horn signal confirms that the sensor identification code has been matched with that tire and tire position.
9. Proceed to the front tire on the passenger's side and repeat the procedure in point 8.
10. Proceed to the rear tire on the passenger's side and repeat the procedure in point 8.
11. Proceed to the rear tire on the driver's side and repeat the procedure in point 8. The horn sounds twice to indicate that the sensor identification code has been matched to the rear tire on the driver's side. The TPMS sensor matching is then no longer active. The "Tire pressure programming active" message is then removed from the driver information display.
12. Turn the key OFF.
13. Readjust the tire pressures to the recommended values.
14. Replace the valve caps on the valves.

Compatible with the following vehicles:


2013 LaCrosse 3.6
2013 Regal
2013 Regal GS
2013 Verano
2012 LaCrosse 3.6
2012 Regal
2012 Regal GS
2012 Verano
2011 LaCrosse 2.4
2011 LaCrosse 3.0
2011 LaCrosse 3.6
2011 Regal CXL
2010 LaCrosse 2.4
2010 LaCrosse 3.0
2010 LaCrosse 3.6


2013 SRX AWD
2013 SRX FWD
2013 XTS AWD
2013 XTS FWD
2012 SRX AWD
2012 SRX FWD
2011 SRX 2.8L Turbo AWD
2011 SRX 3.0L AWD
2011 SRX 3.0L FWD
2010 SRX 3.0L AWD
2010 SRX 3.0L FWD


2014 Impala
2013 Camaro Convertible LT
2013 Camaro Convertible SS
2013 Camaro LS
2013 Camaro LT
2013 Camaro SS
2013 Cruze
2013 Equinox
2013 Malibu
2013 Sonic Hatchback
2013 Sonic Sedan
2013 Spark
2013 Volt
2012 Camaro Convertible LT
2012 Camaro Convertible SS
2012 Camaro LS
2012 Camaro LT
2012 Camaro SS
2012 Cruze
2012 Equinox
2012 Malibu 4cyl
2012 Malibu V6
2012 Sonic Hatchback
2012 Sonic Sedan
2012 Volt
2011 Camaro Convertible LT
2011 Camaro Convertible SS
2011 Camaro LS
2011 Camaro LT
2011 Camaro SS
2011 Cruze
2011 Equinox
2011 HHR LS
2011 HHR LT
2011 Malibu 4cyl
2011 Malibu V6
2011 Volt
2010 Camaro LS
2010 Camaro LT
2010 Camaro SS
2010 Cobalt Coupe with 4 Lug Wheels
2010 Cobalt Coupe with 5 Lug Wheels
2010 Cobalt Sedan with 4 Lug Wheels
2010 Cobalt Sedan with 5 Lug Wheels
2010 Equinox
2010 HHR LS
2010 HHR LT
2010 HHR SS


2013 Terrain
2012 Terrain
2011 Terrain
2010 Terrain


2012 9-4X 3.0i
2012 9-4X 3.0i Premium
2012 9-4X Aero XWD
2011 9-4X 3.0i
2011 9-5
2010 9-5 Aero Sedan

Schrader 20117 TPMS Relearn Procedure

When new tire pressure sensors are installed, they must be registered to the vehicle using a MAGNET.

1. Turn ignition switch to ON position, with engine OFF.
2. Simultaneously press the keyless entry transmitter’s LOCK and UNLOCK buttons until a horn chirp sounds, indicating the relearn mode has been enabled.
3. Starting at the left front tire, place the MAGNET over the valve stem until the horn chirps (this takes approximately 5 seconds).
4. After the horn chirp sounds, proceed as in previous step for the next 3 sensors in the following order: right front, right rear, then left rear.
5. After the left rear sensor ID is learned, a double horn chirp will sound, indicating all 4 sensor IDs have been learned. Turn the ignition switch to OFF position to exit the learn mode.
6. Make sure all tires, including the spare (if equipped), are inflated to the vehicle’s recommended inflation pressures.

Compatible with:


2005 Deville
2004 Deville
2004 Deville DHS
2004 Deville DTS
2004 Seville SLS
2003 Deville
2003 Deville DHS
2003 Deville DTS
2003 Seville STS
2002 Deville
2002 Deville DHS
2002 Deville DTS
2002 Seville STS
2001 Deville
2001 Deville DHS
2001 Deville DTS
2001 Seville STS


2004 Corvette
2004 Corvette Convertible
2003 Corvette
2003 Corvette Convertible
2002 Corvette
2002 Corvette Convertible
2001 Corvette
2001 Corvette Convertible